owa450

CPU

• ARM Cortex A8 at 800MHz clock speed
• Debian Distribution File System*
• NAND FLASH 1GB (Up to 2 GB)
• DDR3 512MB (Up to 1 GB)
• MicroSD card holder for additional storage

*For more information about the OS and kernel, contact us.

GNSS

• Receiver: GPS/GLONASS/GALILEO/QZSS/BeiDou
• 72-channel continuous tracking receiver
• SBAS: WAAS, EGNOS, MSAS, GAGAN
• Update Rate: up to 10Hz
• Accuracy: 2 meters CEP
• Signal Acquisition:
  • Cold Start: 26 s
  • Hot Start: < 1.5 s
• Signal Reacquisition: < 1 s
• Active Antenna Power Supply: +3.3 V

*Features availability depending on the version.

Interfaces

• Up to 4 CAN bus:
  • 2 CAN bus supporting full speed 1Mbps CAN 2.0B
  • 2 CAN FD supporting 8Mbps
• Up to 2 K-line bus
• Integrated sensors: Programmable 9-axis sensor, accelerometer, gyroscope and magnetometer
• TPM 2.0
• 10 configurable digital input/outputs:
  • 50V max inputs (logic low <1.5V, high >3V)
  • All inputs function as wake signals for low-power modes
  • All inputs can be used as counters (odometer). 32bit, 3Khz max
  • 8 open collector outputs (200mA each)
  • 2 high-side switches to Vin for output (1A each)
  • Short-circuit protection for all outputs
• Optional 3 extra digital inputs in the expansion connector
• 4 analogue inputs:
  • 12 bit resolution, 1% accuracy
  • Multiplexed with digital I/O pins
  • 0-5.12V (5mV per bit) or 0-30.72V (30mV per bit) configurable by SW
• Maxim 1-Wire
• MicroSD card holder
• USB Host 2.0
• 3 external RS232 ports. 6 pins configurable by SW as follows:
  • 3 x (TX/RX) or
  • 1 x (TX/RX) & 1 x (TX/RX/CTS/RTS)
• Up to two RS485 port
• Ethernet 10/100Base-TX
• Vout 5V power output (500mA max)
• FAKRA antenna connectors
• 4 LEDs for status indication
• Audio CODEC for external microphone and speaker

*Availability of features depends on models.

Power Supply

• Nominal range of 9 V to 48 V
• Typical consumption at 24 V

Batteries

• Back-up when there is no power supply available
• Standard backup battery for RTC. Duration 10 years
• Optional rechargeable Battery Li-ion 3.7V. Inserted via the rear battery cover

Temperature

LTE Cat 1 with UMTS/HSPA and GSM fallback

• DL 10.2Mbps, UL 5.2Mbps
• GPRS Class B, Class 12 (4&4)
• No standard voice calls support, calls must be done using a SIP client

owa450(P)

• LTE Cat 1 bands: 1, 2, 3, 4, 5, 7, 8, 12, 13, 18, 19, 20, 26, 28, 66
• UMTS/HSPA+ bands: 1, 2, 3, 4, 5, 6, 8, 19
• GSM/GPRS/EDGE: Quad band

Enclosure

• Environmental protection to IP40 standard (protection against dust)
• Dimension: L=150 x W=94 x H=32 mm)
• Weight: 254g
• Material: PC+ABS
• System connectors: Molex Microfit 24-way 43045-2400
• MicroSIM
• MicroSD
• Ethernet RJ45 or M12

Development Kit

• Includes: Developer’s board owa450, power supply cables, cables for interfaces, speaker, microphone, antennas, web access to: cross compiler, API, libraries, manuals and application notes

Other Options:

• See Variants & Options

This table is only an HTML5 version of the official BOK 000 5001 owa450 family variants & options summary, available on the documentation section of the owa450 IoT gateway.

Notes

1. Analog Inputs are multiplexed in the main connector with DIOs (DIN0/AIN0 – DIO1/AIN1 – DIO2/AIN2 – DIO3/AIN3)
2. The iButton is multiplexed with DIO6 and cannot be used simultaneously
3. KLINE shared the pin with DIO-7. RS485 and KLINEs cannot work at the same time (SW selected). 2nd KLINE will share pin with DIO-5 and remove UART 1 TXD1/RXD1
4. CAN 2 removes DIO-2 and DIO-4
5. CAN4 is not compatible with 9 Axis MEMs
6. CAN3 and CAN4 support CAN FD from revision R1B
7. 2nd, RS-485 in OWA450A+ removes UART5
8. In the OWA450I, if the 2nd RS485 is in the main connector, it will remove UART5, DIO5/Kline2 and DIO7/Kline1. If it is in the expansion connector, it will remove UART5